Gone... and first jobs...

Three days later and I'm out, and work has already commenced, but after four days of hard work I'm glad to be back at my desk for a rest!

So Friday was mast down, Saturday was work party at the club for lift out - eight boats lifted and plenty of time on the water (which is a good thing), on a variety of boats (also a good thing), it was mostly sunny (ditto) but my goodness it was chilly...  some biting northerly's..

Sunday Sparrow was due for lift out so arrived early, got a lift out to Sparrow (so no tender required) and motored her under the bridge for one last trip this season before picking up a spare mooring in the pool between the bridge and the old railway line to wait for my turn on the tractor..

Not so bad this year - fourth out I think - and an absolute prime position right by a power/water bollard, and just in front of t'other Dave's boat (he of Jolly Boys "fame")... most chuffed..

Note broom pole as temporary central mast support...

The following makes it look like it was hugely gray and stormy - but that would be because it was ..  we had at least two deluges during the lift out..  hideous....

Enough was enough - outboard engine taken off and flushed with fresh water and I headed home for a warm shower...

With a plenitude of holiday still in the bank at work I had booked off Monday for wash down and hull clean - I had a list and I was going to stick to it! ... 

First on the list was a better mast support - all the years I've had Sparrow I've just hung the mast between the two end points (crutch and pulpit) but with no central support it bounces, and I am wary of issues with putting weight on it while moving about the boat, so for lift out I put in a temporary broom pole and lashing to support the centre, but I wanted to make something more permanent - bit of 3 x 2 later and all done...

Next job (while I waited for the tide to fill in) was to start job #8 which is one of my priority jobs for the winter..  Sparrow has a couple of glassed in metal stringers running from one keel to the other - my guess is that it is keel reinforcement - over the years the glass has split and let in water so the stringers were beginning to rust - not a good thing..  so Monday with the help of the awesome oscillating multi tool I cut away all the glass fibre, to get a good look at what was underneath.. 

Not so bad I was relieved to find - just surface - but needed treating..  I also noticed that the stringers are not directly attached to the surface of the boat underneath which reinforces my view they are not part of the hull reinforcement, but purely for keel reinforcement... I think..  no matter have asked some experts and we shall see...

In the meanwhile I cleaned them off with a wire brush, and then coated them with Fertan [clicky] and left them for the prescribed 24/48 hours

Depending on what I hear, I will either just paint them and leave them exposed (I prefer this one as I like to see stuff, not hide it under glass fibre) or glass them back in (if they are also hull reinforcement). Whatever I choose to do, I will also clean and paint the bilges in the immediate area...

That done and it was time to go recover the mooring pickup chain and buoy - I always do this as I take the view that the pickup chain will last a lot longer living in my garage over the winter than it will lying in the mud and the crud of the harbour bottom..

Last time I installed the chain, purely to see if it would help, I sprayed the thread of the shackle that attaches to the mooring buoy with waterproof grease, and I was hugely pleased to see that this year I could actually undo it rather than having to hacksaw it as I usually do - bonus...

Safely ashore and tender stored, last job of the day was the pressure wash of the hull (which was much needed - see video evidence below) - in the great pantheon of sh*tty jobs that have you to do on a boat, pressure washing underneath the hull, between the keels, is right up there as #2 or #3 (antifouling will always be #1), but an hour later, a considerably soggier Steve was done (O rings had gone on the pressure washer lance, so it was leaking up my sleeve )

Note new mast support...

Got a weeks holiday coming up, so one last session before I go - need to give the decks and cockpit a wash down, and I'll hoover out the dust/debris in the bilge, and wash down the stringers ready for a coat of paint - if they're dry in time, I'll give them a coat of metal primer there and then...

Last of all, the worlds most boring video - purely for interest I like to document what state the hull is in each year on lift out - this is this years, look at that crop of barnacles!

Going, going..

....the Jolly boys convened yesterday for our usual festival of fun as we got the mast down.. remarkably trouble free this year.. damn cold though, and the first major frost of the winter this morning..  roll on next summer, but not so fast as last year please, as I fancy getting some work done this winter!

End of the season...

...so a little under four weeks ago when I said those words "I could come out tomorrow content, but a few more trips would be nice..." they turned out, unfortunately, to be famous last words....

Faced with a succession of low pressure systems featuring rain, wind, rain, storm Callum (must be bad if it got a name), plus a number of family drama's, and so it was that I arrived at the last weekend before lift out to be faced by a high pressure zone over the UK that was so high you'd need a Hubble space telegraph to see how big it was...  beautiful warm sunny weather but not a breath of breeze....

So what does a man do when his boat is coming out of the water the next weekend for a long cold winter and there isn't enough wind to sail? He fires up the metal donkey, drops his mooring, goes in search of an empty mooring, and then starts frying bacon while he watches the world go by...

Bacon sizzling - my permanent mooring is in the far distance - look at that water, flat as a flat thing...

Lovely day on the water, the bacon was good, the coffee was good, I got to watch the boats coming out of Northney, and I sat in the sun..

Bare feet in mid-October - unheard of..

Regrettably time and tide wait for no man so I motored back to the mooring and then stripped the sails, boom, and halyards - the jolly boys are coming on Friday to drop the mast, east pork pies, and drink beer...  I have a work party Saturday (lift crew), Sparrow comes out on Sunday, and I have the Monday off to pressure wash and clean the hull...

Few more jobs added to the winter job list - first one, storm Callum did for my sail cover and the cheap and cheerful I bought way back in 2013 has finally given up the ghost, splitting along the top seam - long term exposure to UV had done for the stitching...  I have a choice - repair it or buy a new one, but given the material is also now as thin as tissue I think a new one can be afforded - it cost me £50 five years ago..  tenner a year? Bargain...  Second, I need to renew the whipping on the genoa/main/topping lift, eyes...